Home > Engine Accessories
Sort By:
Page of 2
CNC Isolator Block for Zenoah 2xx engines CNC Piston Stop for Zenoah Engines DDM Clutch/Fan Wrench
DDM Clutch/Fan Wrench
Our Price: $34.99
Free Shipping
CNC Isolator Block for Zenoah 2xx engines CNC Piston Stop for Zenoah Engines DDM Clutch/Fan Wrench
Flexible Fuel tank clunk line Flexible Vent Tubing - 12" Fuel Inlet Fitting
Fuel Inlet Fitting
Our Price: $9.50
Free Shipping
Highly flexible fuel tank clunk line
Sold by the foot 		5mm OD x 3mm ID vent tubing suitable for fuel tank venting. This is not flexible enough fore use INSIDE the tank Fuel Inlet fitting - includes mounting hardware
Fuel Vent/Fill Fitting G10 Air Deflector Gas Fuel Tank Plumbing Kit
Fuel Vent/Fill Fitting
Our Price: $7.50
Free Shipping
G10 Air Deflector
Our Price: $4.00
Free Shipping
Fuel Vent fitting - includes mounting hardware Air deflector for Zenoah G2xx engines Gas Fuel Tank Plumbing Kit
Gasket Set for CNC Isolator Block - Zenoah 2xx engines Governor Sensor Mount GPH Engine Break-In Oil
Governor Sensor Mount
Our Price: $16.99
Free Shipping
GPH Engine Break-In Oil
Our Price: $4.99
Free Shipping
CNC Isolator Block for Zenoah 2xx engines Governor sensor mount for Zenoah/CY RC format engines. Fully adjustable!

 		GPH Engine Break-In Oil - 4 Oz

Mix entire contents of bottle with 1 gallon of fuel - (gasoline/petrol or lantern fuel)
GPH Gas Helicopter Support Kit GPM Engine Premix Oil - 36:1 GT15 High Performance Cooling Head
Everything you need to setup and support your gas helicopter
 		Tired of measuring just the right amount of oil to mix with fuel for you gas helicopter or car?

Premix oil for your gas helicopter!
  • 100% synthetic
  • Clean Running
  • Exceeds API/JASO Standards
  • Pre-Measured for exact 36:1 mix ratio
  • Sealed containers
Not recommended for use with the GT15 engines
 		High performance cylinder head for GT15 offers cooling improvements
GT15 Teflon Isolator Heat Deflector for Zenoah/CY RC format engine High volume air filter and velocity stack for Zenoah engines
GT15 Teflon Isolator
Our Price: $39.99
Free Shipping
Custom made teflon carburetor isolator for GT15 engines Heat Deflector for Zenoah/CY RC format engine High volume air filter and velocity stack for Zenoah engines
JC Designs Custom Clutch Base JC Designs Fuel Vent Spool JCD Zenoah Propeller Adapter
Custom made clutch base for Zenoah RC Engines Spool to wrap fuel vent lines into a perfect coil
Can be installed over a frame spacer or bolted to the frame
Fully fuel proof 		Have a need to mount a propeller on your Zenoah 23/26/29/240/260/290 based engine? This JC Designs adapter set allows you to mount a propeller for testing, break-in, needle setting or for installation on a craft of some sort.

Wooden propellers and sizes smaller than 14" are NOT recommended.

This set is included with the JCD Engine Running Test Stand.
OS Max GT15 Spiral Pin Retainers Stens Fuel Filter - 12mm` Stens Fuel Filter - 15mm
GT15 Spiral Pin Retainers Stens Fuel Filter - for 12.5mm or larger tank openings (example Trex 700 tank) Stens Fuel Filter - for 15.25mm or larger tank opening
TRM Tru-Run Zenoah Clutch Base Tygon Fuel Line - 1/8" ID x 1/4" OD Walbro WT-1107 Carburetor - no choke
Trued clutch base for the Zenoah RC engine. Genuine Tygon Fuel line
Sold by the foot 		Walbro WT-1107 carburetor with choke removed and sealed.
5% or more power increase over the WT-990 when installed on a 310 engine.
Walbro WT-990 Carburetor XGuard OS Max RPM Unit Zenoah crankshaft clutch bolt
Walbro WT-990 Carburetor
Our Price: $85.00
Free Shipping
XGuard OS Max RPM Unit
Our Price: $39.99
Free Shipping
Walbro WT-990 carburetor. This carburetor is std equipment on the 300 class engines and can also be used on the 310 class engines RPM unit to integrate OS Max EI system with governors. Works with both Futaba and non-Futaba governors Zenoah crankshaft clutch bolt